Datecs LP-50 User Manual

1 DATECS, BulgariaUser’s ManualLABEL THERMAL PRINTERMODEL LP-50

1 DATECS LP-5010— Use a shielding wire or twisted pair wire for a signal line, in order to minimizenoise effect. Do not route the cable too long or co

11User’s ManualPRECAUTIONS FOR HANDLINGDo not handle the equipment in the following manners, because prob-lems may result.— Do not use any other power

1 DATECS LP-5012DAILY MAINTENANCE— At the time of maintenance, be sure to turn off the power switch of the printerand unplug it from the socket.— Use

13User’s Manual1. OUTLINEThis LP-50 is a compact-sized, label thermal printer is designed for various typesof data communication terminals and measuri

1 DATECS LP-50141.2 UnpackingWhen unpacking the package, confirm that the following parts are provided:—Printer body ...

15User’s Manual2. BASIC SPECIFICATIONS2.1 Basic specificationsPrinting system Line thermal dot printingPrinting width 48 mm (384 dots/line)Dot density

1 DATECS LP-50162.2 Paper Specifications2.2.1 Recommended Paper Thermal paper roll Type: Thermal paper Paper width: 58 + 0/–1 mm Paper thickness:

17User’s Manual2.2.2 Recommended PaperThermal paper2.2.3 Printing Head and Paper Cutter Layout

1 DATECS LP-50183. OUTER APPEARANCE AND COMPONENT PARTS(13) RS232 InterfaceDrawer ControlAC adapter(12)Power Conector

19User’s Manual(1) POWER switchTurns on/off the power for the printer body.(2) POWER lampLights green when the printer is switched on(3) ERROR lampFla

THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANYMECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANYCIRCUMSTANCES WITHOUT THE WRITTEN CO

1 DATECS LP-50204. OPERATION4.1 Connecting AC Adapter!CAUTION— Use only the specified AC adapter.— When disconnecting/reconnecting the cable connector

21User’s Manual4.2 Connecting Interface Cable1 Turn off the power. (Mating side included)2 Check the top and bottom of cable terminals, and connect to

1 DATECS LP-5022!CAUTION!CAUTION— The printer cover is not stationary (Opening/Closing). After detaching it,be careful not to lose or break it— Do not

23User’s Manual4.4 Eliminating the Paper Jam- Do not carry out this work just after printing because the printing head is very hot.- Be sure to turn o

1 DATECS LP-50244.5 LEDsPOWER Lights green when the printer is switched on.ERROR Flashes red when the printing head is overheated.PAPER Flashes red w

25User’s Manual5. DIP SWITCH SETTING5.1 Location of DIP Switch1 Turn off the power.2 Detach the printer cover, and take out the paper roll. (The switc

CONTENTS1 OUTLINE ... 131.1 Features ...

1 DATECS LP-504

5User’s ManualIMPORTANT SAFETY INSTRUCTIONS—Read all of these instructions and save them for future reference.—Follow all warnings and instructions ma

1 DATECS LP-506CAUTIONS— Prior to using the equipment, be sure to read this User’s Manual thoroughly.Please keep it handy for reference whenever it ma

7User’s ManualSAFETY PRECAUTIONS – BE SURE TO OBSERVEIn order to prevent hazards to an operator or other persons anddamage to property, be sure to obs

1 DATECS LP-508WARNING— Never handle the equipment in the following manners, as it may break, become out oforder, or overheat causing smoke and result

9User’s Manual PRECAUTIONS FOR INSTALLATION— Do not use or store the equipment in a place exposed to fire, moisture, ordirect sunshine, or in a plac